DIY

Why I Don’t Use Titebond III | MORE MINUTES

Why I Don’t Use Titebond III | MORE MINUTES

source

FacebookTwitterGoogle+PinterestShare
View Comments (20)

20 Comments

  1. nick morrissey

    September 15, 2018 at 9:39 am

    I use super glue as a finish when I'm turning, it damn near always turns out pretty nice

  2. davearonow

    September 15, 2018 at 9:39 am

    Add a red shirt and a white sailor hat and here we have Gilligan.
    Looks like he finally got off the island.

  3. kamulas Laighin

    September 15, 2018 at 9:39 am

    thinner CA glue seems to work a lot better with wood than the thicker stuff, but i only trust it for small turning projects.

  4. Shaun Sayres

    September 15, 2018 at 9:39 am

    I have the same problem with regard to staining the wood when using titebond 3 and it is very frustrating. thankfully it hasnt produced an aesthetic issue yet

  5. Bear utube

    September 15, 2018 at 9:39 am

    lacquer sticks are good for filling nail holes after finishing and can be had in shades to match most woods.

  6. Stan Webb

    September 15, 2018 at 9:39 am

    If when work in the shop you should always have wet shop towel with you at the station you are working from… this is how you will always have it to clean the top of the glue container and any other situation that rises from the course of the day grease, paint, stain, wood resin or just to wipe off a machine or other tool……….

  7. Junk Mail

    September 15, 2018 at 9:39 am

    The BEST CAP iI found for Church Pipe Organ Leather Glue was the RED CAP on Elmer's Glue. I'd go buy a bottle POUR OUT and RINSE OUT the Elmer's Glue and put the LEATHER GLUE into the clean Elmer's Glue bottle, and that system would last a year or two. Where as the Leather Glue bottle would only last 2 or 3 months, and have to buy NEW. At $20 a quart, piss me off. SERIOUSLY the designed Elmer's Glue Orange or Red Cap protected the applicator tip AND the contents of the bottle!!!

  8. grel wood

    September 15, 2018 at 9:39 am

    to comment on your super glue bit of this. " zap a gap " is the two part product that is commonly used. and generally i use it for fixing flaps of grain that pop up after going through the planer.,

  9. Brendon Puckett

    September 15, 2018 at 9:39 am

    My uncle is a boat builder and he only use Titebond III. He says it gives him a longer working time and does better handling the water. I personally like to use Titebond II for my dry land projects.

  10. stevensrspcplusmc

    September 15, 2018 at 9:39 am

    Longer open time

  11. adam moon

    September 15, 2018 at 9:39 am

    holding strength is better and only slightly more "waterproof"

  12. Miss Monday

    September 15, 2018 at 9:39 am

    I don't even do any woodworking, but I am watching you address your opinion on Titbond II and III. You sure are getting me excited to start though! I just need to either get out of my studio apartment, or rent some more space.

  13. Moran Guy

    September 15, 2018 at 9:39 am

    I think squeeze bottle at the dollar store worth the money but not this one which cost like a bottle of brand new glue from elmers or titebond ….

  14. svhsfro4

    September 15, 2018 at 9:39 am

    Godfather III is dog shit, Godfather II is gold and you knew that when you made that nonsense comparison. Quit teeing everything up for your 14 year old suscriber base for the comments

  15. Night Stringers

    September 15, 2018 at 9:39 am

    Salt would water down the glue .Gorilla glue doesn't last. I gave up on that crap and like you say it's a pain in the grain lol to work with

  16. Mark Held

    September 15, 2018 at 9:39 am

    Titebond 3 is junk it is not strong ill stick with the original one its the best.

  17. Harry Powers

    September 15, 2018 at 9:39 am

    Instructive, but I don’t agree with respect to Titebond 3–I’ve been pretty pleased with it and have gone exclusively with it for any outdoor project. So far I haven’t noticed any discoloration at the joints but I DO sand pretty thoroughly after it’s dry.

  18. William Arrington

    September 15, 2018 at 9:39 am

    I know this is old but super glue works when you have a tear out on a corner of a board. Find the splinter. put superglue on then put it back into place using decent pressure. when it cures which doesnt take long at all. lightly sand and you wont be able to tell it broke off and maybe if your really looking for it you will see a tiny hairline fracture which pretty much no one will ever notice

  19. Macks Power

    September 15, 2018 at 9:39 am

    If you need a fast joint but only temporary, I saw a video where they use hot glue. Seems like it might work as well as cyanoacrylate for temporary adhesion but is even faster.

  20. Rendel Anderson

    September 15, 2018 at 9:39 am

    Another personal opinion, by someone who has their own thoughts and isn't reading instructions or product capabilities.

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

DIY

More in DIY

1552851123_maxresdefault.jpg

Biggest wood staining mistakes and misconceptions | Wood staining BASICS

HDMarch 17, 2019
hqdefault.jpg

Make a mystical fortune-telling box

HDMarch 15, 2019
1552678179_maxresdefault.jpg

Planer VS Jointer: What's the Difference? | Woodshop 101

HDMarch 15, 2019
1552505214_maxresdefault.jpg

How to Home Podcast | #8 "Designing Your Dream Space w/ Pure Salt Interiors"

HDMarch 13, 2019
1552332306_maxresdefault.jpg

Introducing a New Way to Make Pencils // Woodworking Project

HDMarch 11, 2019
1551986394_maxresdefault.jpg

How to Home Podcast | #7 Renting vs Buying: Is Buying the Best Option?

HDMarch 7, 2019
1551467561_maxresdefault.jpg

How to Turn a Failure into a Disaster | Woodworking Project

HDMarch 1, 2019
1551467425_maxresdefault.jpg

18 things every beginning woodworker should know

HDMarch 1, 2019
1551467392_maxresdefault.jpg

How to Home Podcast | #6 "Architectural Design & Pulling Permits"

HDMarch 1, 2019